How to plunge cut with a fixed base router advice, Home repair and maintenance guide, Property fix equipment tips
How to Plunge Cut with a Fixed Base Router?
post updated 24 February 2024
If you work in a professional woodworking shop, you already know the importance of a fixed base router! Yes, it does all the work of cutting without taking the help of any other equipment! But do you know you can also plunge cut with this one?
Yes, you can! And how to plunge cut with a fixed base router if you do not have a plunge router? We will tell you every detail, from the router bits to use, to cleaning afterwards! Here is the method of cutting the perfect plunge cut without having a plunge router!
5 March 2022
Step by Step Fixed Base Router Plunge Cut
Go through the step-by-step method of making a plunge cut with the help of a fixed base router! Yes, no need to invest in any other equipment anymore!
Step 1: Get the Jig
First of all, you have to get a jig so that it is easy for you to keep the router base added to the bit cuts. If you do not use it, the router base will start moving when you will work. And eventually, it will get out of control keeping the raw materials beside! So, the first job is to get the jig for your safety.
Step 2: Examine the Base
Go through the jig and check the three particles. A 1/4 –inch plywood is used for the base here. There is a cut down in the middle too. This is for the approval of a straight bit. And then you will see a set of two fences. They will be set beside one another. These fences are 2’ x 4’ and are set in one straight line on top of the router base. Here, the cutting range will be marked with the top blocks.
Step 3: Set it up
The setting of the bit should be set for an immense cut of ¼ inches. Make sure it is set properly. Once you are done, you have to get your hands on the router and position it at an angle. Go through the router base’s one side. Hold it against the jig’s base. Make sure your hand is firm enough to hold it strongly. Slowly, you have to get your hand on the bit and take it low.
Take it into the slow inside in your jug. After a while, you will see that the router is leveled on the base of your jig. When you switch on the router, make sure you are noticing the sound of your motor. It is an easy way to tell if the router is cutting the wood properly and safely or not.
Step 4: Start Working
It’s time for you to start the router. Hold it and flit it both backward and forward. You have to stop at the boundaries at the front and back. Yes, the routing direction might confuse you. But you don’t have to worry about it. Keep in mind that the fences are there to keep the router aligned.
Some shallow passes might require depending on how extreme you want to cut! While operating the router, make sure that you are going for the speed that you can handle. Make sure you have control over the speed of your router. Also, nourishing the router bit into the material firmly is necessary.
Step 5: Stop and Clean
After you are done, make sure you do not let the router go out of your hands. Yes, you have to firmly hold the handle of your router till the motor of the router stops moving or working. If you think that there are any issues or you have to fix the router down, make sure that the motor of the router stops first and then you go for it.
While operating, do not try to get into its work, it might result in an accident. After the work is done, you have to switch off the router. But don’t forget to clean it. There will surely be particles that will stick into the router! You don’t want the router having any issue with starting the next time you use it, right! So, go through the parts of your router and clean them carefully.
FAQs on Cutting Plunge with Fixed Base Router
Is a plunge router different from a fixed base router?
Yes, there are differences between plunge routers and fixed base. The bit of the fixed base one, as the name says is designed to be set in a fixed position. And you can lower the bit of a plunge router and keep the base plate flat on the stock. However, both the plunge router and the fixed base router have adjustable depths for cutting and you can select them according to your preference.
What does a fixed-base trim router do?
As the base of the fixed base routers stays in the same position, you will good grade of precision while working. Along with this, they have the cutting depth preset. So, you won’t be dealing with any human error with this one! In joinery projects, a fixed base router is loved because they are great for working from the sides or edging!
Can I use a plunge router for edges?
Both the plunge routers and the fixed base router are amazing for working with the sides or the edges, especially for decorative cuts. At times, you need to work on the inner part of a surface.
In the case of the keyhole slots or mortises, this happens often. And this is where the plunge router comes in. The best part is you can get routers that are available for switching between plunge bases and fixed bases. These are great for both jobs!
How to plunge cut with a fixed base router – Wrap Up
Now you already know how to deal with a fixed base router and make plunge cuts with this one! The steps are easy and all you need is to pay attention!
Not to forget, you must wear the necessary protective gear for woodworking or metalworking before you start the work process. And trust us; the method isn’t going to disappoint you!
Comments on this guide to how to plunge cut with a fixed base router? article are welcome. We welcome your advice on this cutting process explanation. Do you have a different take on this subject?
Woodworking and Carpentry
CNC and Laser Cutting
Woodworking and Joinery / Carpentry
Home Improvement Articles
Comments / photos for the How to plunge cut with a fixed base router advice page welcome.